CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.
|Published (Last):||12 April 2012|
|PDF File Size:||14.5 Mb|
|ePub File Size:||8.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Shut down all the ports on your current root switch.
This can cause traffic to be process-switched using the routing table, lzb of fast-switched using the route cache. The cost shown here is for the port.
CCNP SWITCH Lab Manual, 2nd Edition
Demonstrate root guard functionality. Enter the email address you signed up with and we’ll email you a reset link. Create a subinterface for each VLAN. If the sender port priorities are the same, the switch picks the port that receives BPDUs with the lowest sender port number.
Ccnp Tshoot Lab Manual Configuration Files – downloadsoftspecialists
Check the configuration using the show ip access-list and show ip interface vlan vlan-id commands. Information obtained through CDP saitch used to determine when an IP phone is attached to the access port. To find out how the router is configured, look lav the interfaces to identify the type of router and how many interfaces the router has.
The standby command is also used to configure the IP address of the virtual gateway and configure the router for preemption. This places you at the user EXEC prompt.
Disable the links between the access layer switches. The switch warns you about the possibility of creating switching loops. In addition, configure a loopback interface on the ISP router to simulate an external network. You do not need to leave configuration mode to execute this command.
On each switch, erase the startup configuration, delete the vlan. DLS1 show etherchannel summary Flags: Optionally, configure an enable secret password and console awitch. Although not configured in this inwtructor, loop guard can be configured as an alternative or in addition to UDLD. February January Your output might look different depending on the switch model that you are using. If you accidentally type yes, you can break out of the initial configuration dialog at any time by pressing Ctrl-C.
If that is the case, read through those portions of the lab that deal lsb their configuration to become familiar with the process instruvtor commands. Did the topology converge the way you thought it would?
To change the priority for a given VLAN, use the spanning-tree vlan number priority number command. Creating vlan VLAN was created at the same time port 6 was assigned to it.
Each route processor swiych route between the various SVIs configured on its switch. The VLAN database and startup configuration need to be deleted. DLS2 debug spanning-tree events Spanning Tree event debugging is on b.
Configure HSRP interfaces and enable routing. Configuring DHCP snooping on the access layer switches involves the following process: Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Which pings should succeed and which should fail?
Use the question mark on the interface level command spanning-tree vlan number?. The following is a sample configuration for the trunks and EtherChannel from DLS1 to the other three switches. You should receive responses. The Cisco Networking Academy curriculum consists of swktch experience- oriented courses that employ industry- relevant instructional approaches to prepare students for professional- level jobs: To enable security on a port, you must first issue the switchport port-security command by itself.
The distribution layer switches act as Layer 3 devices and do not need default gateways. The access layer ccp act as Layer 2 devices and need a default gateway to send traffic off of the local subnet for the management VLAN. This lab assumes that you have completed LabClearing a Switch.
EtherChannel is used for these trunks. By default, how many lines are available for Telnet on the access switches? Configure mabual switch parameters. Optional To reset the WLAN controller, use the clear controller swicth followed by the reset system command. Verify that VTP traffic has passed between the switches by comparing the non-zero VTP configuration revision using the show vtp status command.
In addition, switches with a more preferred i.
You can use other switches such as a or and Cisco IOS Software versions if they have comparable capabilities and features. DTP is sent over dynamic oab, dynamic desirable and static trunk ports only Step 3: Signed out You have successfully signed out and will be required to sign back in should you need to download more resources. This command automatically activates access mode, PortFast, and removes all associations of the physical switch port with the port-channel interfaces if there are any.