CP2E – read user manual online or download in PDF format. Pages in total: from the Crestron website (). 2. CP2E only. 2- Series Engine. At the heart of the CP2 & CP2E is the powerful bit Freescale. Crestron CP2E Pdf User Manuals. View online or download Crestron CP2E Operation Manual.
|Country:||Sao Tome and Principe|
|Published (Last):||9 August 2015|
|PDF File Size:||8.39 Mb|
|ePub File Size:||16.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Only the required pins for each communication type should be connected. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause crestrron interference to radio communications.
Page of 28 Go.
CRESTRON CP2 OPERATION MANUAL Pdf Download.
The Software is designed as a software development and customization tool. Cresnet is the communications backbone for many Crestron touchpanels, keypads, lighting controls and other devices. To utilize the creestron strip, determine the number of relays to be commoned for the equipment being installed. If any part of this Agreement is found void and unenforceable, it will not affect the validity of the balance of the Agreement, which shall remain valid and enforceable according to its terms.
Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Secure the ear to the unit with three screws from step 1, as shown in creatron following diagram.
This may result cp22e a conflict with some equipment and therefore all nine pins should not be used.
Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. If this equipment does cause harmful interference to radio or television reception, which can crestorn determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Cpp2e Program Detail View.
Repeat procedure steps 1 through 3 to attach the remaining ear to the opposite side.
Failure to do so could cause equipment damage or void the Crestron warranty. If rack mounting is not required, rubber feet are provided for tabletop mounting or stacking. Verify that serial cable is wired correctly for RS, or To install the ears: The pinout of each 9-pin port is non-standard; it contains Kanual pins in addition to RS Operations Guide — DOC. This document was prepared and written by the Technical Documentation department at: First-time users will need to establish a user account to fully benefit from mnual available features.
This Agreement may only be modified by a writing signed by an authorized officer of Crestron.
Crestron electronic CP2E User Manual
Each network device must have a unique Net ID. Refer to software release notes or Crestron manial for other required Crestron software packages. Page 2 This document was prepared and written by the Technical Documentation department at: Passthrough Mode enables Viewport access to any serial controlled device on the network. You may not transfer the rights of this Agreement to a backup copy unless the installed copy of the Software is destroyed or otherwise inoperable and You transfer all rights in the Software.
Contact with thermal insulating materials should be avoided on all sides of the unit. This link will provide a list of product manuals arranged in alphabetical order by model number.
Crestron CP2E Manuals
Refer to caution statement below. Insert the tinned connection into the Cresnet connector and tighten the retaining screw. CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has cresteon subjected to misuse, accidental damage, modification, or improper installation procedures.
Apply solder only to the ends of the twisted wires. Windows is a registered trademark of Microsoft Corporation. Cresnet power usage of the entire chain.
Crestron CP2 Operation Manual
In the event that msnual clock fails, only an authorized technician should replace it. Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. Such flexibility can offer a cost-effective solution for system expansion, providing a host of additional control ports in a single module. Use care in wiring installations to avoid applying 24 VDC to Cresnet wiring from an AC power pack as well as from a system device that contains its own power supply.